Carp Catchers Blog

The New Rig Marole Bore Rings are an ingenius idea to make bait attachment, fast, simple and effective. No more searching for that lost baiting needle or dropping your last bait stop on the floor, you simply have to screw your bait into place. The Bore Rings are designed to be used with D-rigs, Chod rigs, Blowback rigs etc, basically any rig you would normally have a ring on the rig which your bait is attached to.

The Bore Rings are very versatile in the range of baits they can accomodate. The Bore Rings are ideal for anything from Boilies, Pop ups, Corkball pop ups, Pellets, Artificial Baits, Maize, Nuts and other hard particle baits.

The simple idea of the Bore Rings enables anglers to quickly change their baits without the need for baiting needles, bait stops, rig rings or bait floss.

The rig shown is one of many applications for the Bore Rings, they can even be used for zig rigs and surface fishing. These have been tried and tested, your bait will not come off on the cast.

Give ‘em a go! To purchase click on any of the above links.

Tight Lines

Dave

Zig rigs or Zigs as they are more commonly called can be a very effective method of angling when the carp are up in the water and not interested in feeding on the bottom. Here is a Zig caught 25lb14oz mirror from last week that was caught 2ft under the surface in 12ft of water on a hot day when the carp could be seen sitting under the surface soaking up a bit of sunshine. The fish was caught using Drennan Super Specialist Barbel Hooks and a small artificial bait.

Tight Lines

Dave

Avid Carp Corn Stops combine the benefits of an imitation bait with a boilie stop, mimicking grains of sweetcorn perfectly. They are available in long and short to suit different hair lengths, it also enables you to change bait size without the need to tie new rigs. The Avid Carp Corn Stops are made from durable plastic and come in bright and visual colours to draw attention to your hookbait whatever the conditions.

Step 1

Thread your choosen bait onto the hair.

Step 2

Attach the Corn Stop to the hair loop via the hook on the underside of the stop.

Step 3

Pull the Corn Stop into the bait and your ready to go.

Tight Lines

Dave

Avid Carp Sight Stops are a useful boilie stop that adds visual attraction to your hookbait. They are available in long and short to suit your hair length and enable you to change bait size without tying up new rigs. The Avid Carp Sight Stops are made of a durable plastic and come in a range of bright and visual colours to draw attention to your hookbait in any conditions. The Avid Carp Sight Stops are availble in either Yellow or Mixed Colour packs.

Step 1

Thread your choosen bait onto the hair.

Step 2

Now attach the Sight Stop to the hair loop via the hook on the underside of the stop.

Step 3

Pull the stop into the bait and you are now ready to go.

Tight Lines

Dave

This is a simple surface rig that will compliment the Korda Surface Controllers or any other surface set up.

To tie this rig you will need some Korda Cruiser Control Surface Line, Korda Mixa Hooks, some Enterprise Imitation Dog Biscuits and a Korda Size 11 Ring Swivel.

Step 1.

Remove about 3-4 foot of Korda Kruiser Control Surface Line and tie a small loop knot in one end.

Step 2.

Now thread on an Enterprise Imitation Dog Biscuit. Place one of the supplied shot in the hair loop and pinch in place, then pull it tightly into the recess in the biscuit.

Step 3.

Pass the other end of the line through the back of the eye of the Korda Mixa hook and position it below the bait. Then hook the imitation mixer on the side opposite the shot.

Step 4.

Whip the line up the shank of the hook 6 times making sure the first whip goes away from the join in the eye.

Step 5.

Now whip the line once back down the shank of the hook.

Step 6.

Pass the line through the back of the eye again and moisten before tightening down gently.

Step 7.

Now slide the hook round further so the shank is inside the imitation dog biscuit with the point of the hook free to get a hook hold.

Step 8.

Tie the other end of the hooklink to a size 11 ring swivel using a palomar knot. Double over the end of the hooklink and pass it though the big eye of the swivel.

Step 9.

Now form an overhand knot in the doubled over section of the hooklink around the swivel.

Step 10.

Pass the swivel through the loop in the end of the hooklink which was made when the overhand knot was formed.

Step 11.

Moisten the knot and tighten it down gently before trimming the tag end.

The rig is now ready to be attached to your surface setup and cast out.

Give it a go.

Tight Lines

Dave

The Atomic Tackle Maggot Rig uses the inline lead setup fished helicopter style allowing a large PVA stocking of maggots to be tied to the swivel at the base of the lead. This enables the hook to be secured to the PVA stocking so once cast out the PVA bag will melt leaving your maggot hookbait lying in amongst the other maggots.

For the purpose of the demonstration I used a Gardner Readymade Mag Aligner Rig.

Step 1.

Pull out the large ring swivel from the base of the lead.

Step 2.

Now thread your mainline through the lead. ( If using leadcore or a leader, you will need to splice or loop the swivel on)

Step 3.

Tie your mainline to the swivel, I would suggest a palomar knot. To tie a palomar knot double over your mainline and pass it through the eye of your swivel.

Then tie an overhand knot with the doubled over mainline.

Now pass the swivel through the loop made by the overhand knot.

Then moisten the knot, slowly tighten it down and trim the tag end.

Step 4.

Once the knot is tied pull the swivel into the insert in the base of the lead.

Step 5.

Now you need to either tie your rig to the swivel above the lead. If the rig has a loop in the end pass the loop through the swivel before passing the hookend of the rig through the loop and tightening as I’ve done in this demonstration.

The finished rig should look like this.

The large ring at the base of the lead is for the PVA mesh bag to be tied to, then all you need to do is push the hook through the PVA mesh to secure it for casting.

Give it a go.

Dave

Another single hookbait which could be utilised well in the winter is artificial baits, preferably the flavoured or high-viz variety as they need some attraction to them. The Enterprise Artificial Boilies 10mm , the Niteglow Eternal Boilies and the Solar Everlasting Hookbaits are all top artificial baits that will work well as single hookbaits. Don’t discount artificial sweetcorn as a single winter bait either the ever popular Enterprise range or the new Cotswold Bait Creations Soft Floating Corn. Imitation baits are resistant to nuisance fish, won’t lose bouyancy, go soft or lose attraction.

Give them a go.

Dave