The Bore Rings are very versatile in the range of baits they can accomodate. The Bore Rings are ideal for anything from Boilies, Pop ups, Corkball pop ups, Pellets, Artificial Baits, Maize, Nuts and other hard particle baits.

The simple idea of the Bore Rings enables anglers to quickly change their baits without the need for baiting needles, bait stops, rig rings or bait floss.

The rig shown is one of many applications for the Bore Rings, they can even be used for zig rigs and surface fishing. These have been tried and tested, your bait will not come off on the cast.

Give ‘em a go! To purchase click on any of the above links.

Tight Lines

Dave

Tight Lines

Dave

Step 1

Thread your choosen bait onto the hair.

Step 2

Attach the Corn Stop to the hair loop via the hook on the underside of the stop.

Step 3

Pull the Corn Stop into the bait and your ready to go.

Tight Lines

Dave

Step 1

Thread your choosen bait onto the hair.

Step 2

Now attach the Sight Stop to the hair loop via the hook on the underside of the stop.

Step 3

Pull the stop into the bait and you are now ready to go.

Tight Lines

Dave

To tie this rig you will need some Korda Cruiser Control Surface Line, Korda Mixa Hooks, some Enterprise Imitation Dog Biscuits and a Korda Size 11 Ring Swivel.

Step 1.

Remove about 3-4 foot of Korda Kruiser Control Surface Line and tie a small loop knot in one end.

Step 2.

Now thread on an Enterprise Imitation Dog Biscuit. Place one of the supplied shot in the hair loop and pinch in place, then pull it tightly into the recess in the biscuit.

Step 3.

Pass the other end of the line through the back of the eye of the Korda Mixa hook and position it below the bait. Then hook the imitation mixer on the side opposite the shot.

Step 4.

Whip the line up the shank of the hook 6 times making sure the first whip goes away from the join in the eye.

Step 5.

Now whip the line once back down the shank of the hook.

Step 6.

Pass the line through the back of the eye again and moisten before tightening down gently.

Step 7.

Now slide the hook round further so the shank is inside the imitation dog biscuit with the point of the hook free to get a hook hold.

Step 8.

Tie the other end of the hooklink to a size 11 ring swivel using a palomar knot. Double over the end of the hooklink and pass it though the big eye of the swivel.

Step 9.

Now form an overhand knot in the doubled over section of the hooklink around the swivel.

Step 10.

Pass the swivel through the loop in the end of the hooklink which was made when the overhand knot was formed.

Step 11.

Moisten the knot and tighten it down gently before trimming the tag end.

The rig is now ready to be attached to your surface setup and cast out.

Give it a go.

Tight Lines

Dave

For the purpose of the demonstration I used a Gardner Readymade Mag Aligner Rig.

Step 1.

Pull out the large ring swivel from the base of the lead.

Step 2.

Now thread your mainline through the lead. ( If using leadcore or a leader, you will need to splice or loop the swivel on)

Step 3.

Tie your mainline to the swivel, I would suggest a palomar knot. To tie a palomar knot double over your mainline and pass it through the eye of your swivel.

Then tie an overhand knot with the doubled over mainline.

Now pass the swivel through the loop made by the overhand knot.

Then moisten the knot, slowly tighten it down and trim the tag end.

Step 4.

Once the knot is tied pull the swivel into the insert in the base of the lead.

Step 5.

Now you need to either tie your rig to the swivel above the lead. If the rig has a loop in the end pass the loop through the swivel before passing the hookend of the rig through the loop and tightening as I’ve done in this demonstration.

The finished rig should look like this.

The large ring at the base of the lead is for the PVA mesh bag to be tied to, then all you need to do is push the hook through the PVA mesh to secure it for casting.

Give it a go.

Dave

Give them a go.

Dave