Carp Catchers Blog

The Solar Quick Change PVA Bag System is ideal for anglers who use PVA bags for the majority of their angling. The system will ensure you don’t lose the bag on the cast while improving casting distance and accuracy. The system is designed to be anti tangle and works with any inline lead.

For the purpose of this demonstration I used a Korda Flat Pear Inline Lead, Solar Contour Super Supple Rig Tubing and Korda Size 8 Ring Swivels  was used between the helicopter beads for the rig to be attached to.

Step 1.

Thread your mainline through your desired length of the Solar rig tubing.

Step 2.

Now thread 1 of the beads provided with the Solar PVA System onto the rig tubing followed by the Korda Ring Swivel followed by another bead. If you’re using mainline straight through there is silicone tubing provided for the beads to the grip. If you’re using leadcore then please ensure all beads can be pulled free of the leader to ensure the lead will be lost in the event of your line breaking. Tie or loop your hooklink to the ring swivel.

Step 3.

Now thread on one of the sleeves provided and push the tubing securely inside.

Step 4.

Then gently push the insert out of your choosen inline……

…..and thread it onto your mainline.

Step 5.

Tie a Figure Of Eight Loop Knot  in the end of your mainline and attach the Solar quick change PVA bag clip like so.

Step 6.

Now pull the lead over the clip followed by the sleeve and rig tubing. The finished setup should look like this.

All you have to do to attach a PVA bag is to pull the clip out of the bottom of the lead and hook a PVA bag on before pulling the clip back inside the lead. Then just thread the hook through the mesh of the bag and your ready to cast out.

This set up is particularly well suited to adding freebies with the Mag Aligner Rig and really comes into it’s own during the winter months.

Give it a go.

Tight lines

Dave

The Atomic Tackle Maggot Rig uses the inline lead setup fished helicopter style allowing a large PVA stocking of maggots to be tied to the swivel at the base of the lead. This enables the hook to be secured to the PVA stocking so once cast out the PVA bag will melt leaving your maggot hookbait lying in amongst the other maggots.

For the purpose of the demonstration I used a Gardner Readymade Mag Aligner Rig.

Step 1.

Pull out the large ring swivel from the base of the lead.

Step 2.

Now thread your mainline through the lead. ( If using leadcore or a leader, you will need to splice or loop the swivel on)

Step 3.

Tie your mainline to the swivel, I would suggest a palomar knot. To tie a palomar knot double over your mainline and pass it through the eye of your swivel.

Then tie an overhand knot with the doubled over mainline.

Now pass the swivel through the loop made by the overhand knot.

Then moisten the knot, slowly tighten it down and trim the tag end.

Step 4.

Once the knot is tied pull the swivel into the insert in the base of the lead.

Step 5.

Now you need to either tie your rig to the swivel above the lead. If the rig has a loop in the end pass the loop through the swivel before passing the hookend of the rig through the loop and tightening as I’ve done in this demonstration.

The finished rig should look like this.

The large ring at the base of the lead is for the PVA mesh bag to be tied to, then all you need to do is push the hook through the PVA mesh to secure it for casting.

Give it a go.

Dave

The Guru Pellet Cones  are an innovative alternative to PVA bags that enables an angler to present a small pile of feed around the hookbait. The tangle free presentation that the pellets cones provide is ideal for use with small soft pellets or groundbait.

The pellets I used in this demonstration were Dynamite Baits Marine Halibut Pellets.

If your using groundbait or softened pellets start from step 4. If your using harder pellets and are scolding them follow steps 1-3 first.

Step 1.

Pour the pellets into the bottom of a bait container.

Step 2.

Now pour boiling water over the pellets until they are all just covered over with the water and leave for 20-30 mins.

Step 3.

After 20-30 mins the pellets should still resemble their original shape but they should be soft to touch and lighter in colour.

Step 4.

Now take the pellet cone and hold it from the thin end.

Step 5.

Gently scoop some pellets into the cone, compressing them in as you go.

Step 6.

Once the cone is full compress it firmly with finger and thumb.

Step 7.

Now pass the fine baiting needle through the pellet cone, going in from the wider end and out the thinner end. Your now ready to pull your baited rig through the pellets, once you’ve pulled your rig through remove the cone and its ready to cast out.

The compressed pellets will look like so when attached to your rig.

Once cast out the pellets will hold together until they reach the bottom.

Within 30 seconds they will have broken down leaving a small neat pile of bait around your hookbait…..

Give them a go.

Tight Lines

Dave

The  MCF Dumper Lead Clip  is a very clever and innovative lead clip that is guaranteed to drop the lead in the event of a fish snagging or weeding you up. The tapered sleeves incorporated in this lead clip system help to minimise tangles. This Carp Catchers Blog will show you step by step how to set it up.

These can be set-up with any form of leader or tubing but for the purpose of this demonstration I used a ready spliced leadcore leader.

Step 1.

Using a bait needle thread the small rubber sleeve onto your leader or tubing.

Step 2.

Now you need to pass your spliced leader loop through the metal loop on the lead clip. Or tie on your mainline with your rig tubing already threaded on (Miss steps 3 and 4).

Step 3.

Then pass the lead clip through the loop in the end of your leader.

Step 4.

Pull the leader to secure the loop around the metal loop.

Step 5.

Push the small rubber sleeve over the metal loop.

Step 6.

Now push a baiting needle through the longer sleeve from next to the metal hook out of the tapered end and latch the baiting needle onto your choosen rig.

Step 7.

Once you’ve pulled your hooklink through loop it over the metal hook.

Step 8.

To finish the setup pull the hooklink tight and clip on a lead.

The lead should not eject on a normal force cast, however if a distance cast is required I would suggest securing the lead in place with PVA tape.

If you are using rig tubing then adapt the instructions accordingly.

Tight Lines

Dave

Its getting to that time of year again when maggots are becoming more widely used due to them being such an effective winter bait. Have a go at tying this rig and see how you get on.

The components used in this demonstration were the Korda IQ2 Xtra Soft Fluorocarbon , Korda Wide Gape  hook size 8 and  Korda Micro Rig Swivel.

Step 1.

After cutting your required length of fluorocarbon tie on a Korda Wide Gape using a knotless knot making sure to whip round the shank twice on the way back down to the eye. 

Step 2.

Now thread a micro rig swivel onto the tag end above the hook.

Step 3.

Then pass the tag end through the back of the eye to the front and trim the tag end down to about 3-4mm. This will have created a D shape on the back of the shank for the swivel to move on.

Step 4.

Holding the hooklength out of the way slowly blob the tag end with a lighter to secure it in place. Make sure not to burn the hooklink as this will damage the fluorocarbon and increase the chance of it breaking. Also take care not to burn yourself.

Step 5.

To finish the rig tie a figure of eight knot in the other end setting the desired length of rig you require and trim the tag end.

The finished rig should look like this.

This rig works best with a large bunch of maggots and a couple of imitation pop-up maggots to help counter the weight of the hook. This rig isn’t strictly a maggot rig and can be used with other baits as well. 

The knots used in this demonstration can be found in previous blogs by using the search bar on the top right hand side of the page.

Give it a go.

Tight Lines

Dave

A method that works well over a bed of scattered boilies is mesh PVA bags of boilies. Using something like  Korda Boilie Funnel Web , a tight mesh bag can be created that practically explodes in the water spreading your hookbait and freebies a few inches apart making the trap less obvious to wary carp. The method is to tie a mesh bag with three boilies in a triangular shape as tightly as possible to create the tension in the PVA, which is needed to throw the baits apart upon melting.  When in the water PVA tightens and pulls the boilies even tighter together before the bags burst and catapulting the baits in seperate directions. The triangles are better than the normal linear mesh bag over choddy bottoms as the hook sits in the middle keeping it clear of any chod. However they obviously will not cast as well.

To tie these PVA bags you need some Korda Boilie Funnel Web PVA, scissors and some boilies, these are air dryed Mainline Activ-8 .

Step 1.

Place three boilies in the boilie funnel web tube and allow them to drop out of the bottom into the PVA mesh. If you are using baits over 16mm then I’d suggest using the largerKorda funnel web size as you won’t be able to create the right shape with the larger baits in the boilie funnel web, for baits 16mm and under the boilie funnel web is best.

Step 2.

Now push the baits into a triangular shape and tighten the PVA holding the baits as close together as possible to create a bait triangle.

Step 3.

Holding the boilies in position tie off the bag, again trying to hold the baits as tight as possible. The tighter the bag the better presentation you will achieve.

Once you have trimmed the tag ends of the knots tied in the bag you should have a mesh bag that looks like this. (See Picture Below).

The mesh bag can be hooked on or alternatively you can thread the hooklink through the middle of the baits and pull you hook through to sit between the three baits, this can actually help the slow the rig down as it travels through the water so might be worth a go fishing over softer lakebeds and as I said earlier keep the hook clear of any chod.

Here is a couple of pictures demonstrating the presentation this bag will give your freebies.

The bag still intact.

15-20 seconds after contact with the water.

Give it a go

Tight lines

Dave

Stick fishing is a very advantageous method of fishing as it helps illiminate tangles, can be cast long distances and leaves very little in the way of food items around the hookbait but maximises attraction. Once mastered stick fishing could help you put more carp on the bank.

All that is required to make a good dynamite stick is some Korda Funnel Web Pva, a compressor, some groundbait which in this case is Dynamite Swim Stim Amino Black and a PVA Friendly liquid or oil. Make sure you use a winterised oil for your winter sticks, these won’t congeal and have an adverse affect on the melt time of your PVA.

TFG Gunk Liquids or Winterised fish oils are ideal for stick mixes during the colder months as well as the colder ones.

Step 1.

Firstly pour your chosen groundbait into a container, I use an old pop-up pot which means I can store my mix away to avoid it drying out.

Step 2.

If preferred you can now crumble in a few boilies of your choice to customise your mix. A Korda Krusha can be used to get the finest of boilie dust. If done using your hands Id suggest gently agitating the tub, this will bring the larger items to the top of the mix which you can now crumbled further.

Step 3.

Add your chosen liquid or oil bit by bit making sure to thoroughly mix it in as you go so not to add too much, you want a slightly damp but firm mixture. It is important to get the consistency of the mix correct so it compresses properly. Now leave the mix to absorb the liquid for atleast 20 mins before making your sticks or adding more liquid or groundbait if necessary.

Step 4.

Once mixed thoroughly scoop the desired amount of the stick mix into your funnel web PVA system.

Step 5.

Now for the important part, using the compressor stick from your PVA funnel web system while holding your thumb over the end of the system compress the mix as hard as you possibly can, the firmer the better.

Step 6.

While holding the PVA tight push the compressed mix out of the end.

Step 7.

Now trying not to break up the mix in the bag tie it off as tightly as possible.

Step 8.

Tie another knot in your mesh and cut the pva between them.

Step 9.

Trim the ends of the knots down carefully and your bag is now ready to thread up your hooklink.

Dynamite sticks are ideal for winter fishing where you want as little food items as possible around the hookbait but maximum attraction.  They are alsp effective during the warmer months. Adding winterised fish oils during the winter can maximise the pulling power they have during the colder months. Another little edge, if you don’t want to use fish oils, is to use Mainline Hemp Oil  as this naturally does not congeal in cold water conditions.

If you’d much rather buy a ready made stick mix that doesn’t require any preparation then Mainline’s Pro-Active Stick&Bag Mix-Crushed Tiger Nut or Dynamite Bait’s Monster Tiger Nut Stick Mix and The Source Stick Mix are ideal.

Give them a go.

Dave

Most chod rigs nowadays are setup using leadcore or some form of leader but not all fisheries allow leaders whether they be leadcore or otherwise. Using rig tubing is an option which can help get round these bans and can also be used on waters without bans as an alternative to leaders. Rigmarole have designed Chod Rig Beads to fit their Freefall Micro Rig Tubing so that chod rigs can be tied up safely and effectively using the Freefall Micro Rig Tube. The  Rigmarole Freefall Micro Rig Tube is a plastic coated stainless steel coil so it is extremely tough and heavy, it is also very easy to thread.

The components used in this demonstration were Rig Marole Freefall Micro Rig Tube,  Rigmarole Freefall Micro Rig Tube Chod Beads, Rig Marole Tail Rubbers and a Rig Marole Tournament Casting Lead.

Step 1.

Cut the Freefall Micro Rig Tube to your desired length and thread your mainline through it.

Step 2.

Now thread a Freefall Micro Rig Tube Chod Bead onto the tubing, followed by your chod rig and a second bead. Set the beads in place with your chod rig at the required distance up the tubing.

Step 3.

Thread the Rig Marole  Free Fall Tail Rubber onto the line and push the rig tubing into it.

Step 4.

Now tie on your desired lead with a Palomar knot.

Step 5.

Push the swivel into the tail rubber and pull the line tight through the tubing.

The finished rig should look like this. This rig can also be constructed using the Rig Marole Free Fall Rig Tube  and the Rigmarole Freefall Chod Beads. Warning !!! do not superglue the beads or pierce through the side!!!

Tight Lines

Dave

Tying a zig rig is simple, all you need is a good hooklink material like the Ultima Power Zig, a strong hook and a small section of silicone tubing.

The rig components used in this demonstration were Ultima Power Zig hooklink, ESP Big T Carp Hook and ESP Silicone Tube .

Step 1.

Cut the Ultima Power Zig to your desired length.

Step 2.

Now tie a small overhand loop in one end for your hair stop and thread on your desired choice of pop-up or foam followed by a bait stop.

Step 3.

Then cut a small section (2-3mm) of silicone tubing and thread it onto your zig hooklink.

Step 4.

Now thread the point of the hook through the silicone tubing heading towards the bait and set the hair length at about 2-3mm with the tubing sitting at the top of the shank.

Step 5.

Now tie a knotless knot and don’t forget to whip the hooklink back round the knot once on the way towards the eye to prevent it from slipping.

Step 6.

To finish the zig rig off tie a figure of eight knot at the other end.

The zig rig is now finished and ready to use.

If you are not sure about any of the knots use the Carp Catchers Blog search bar to navigate to the relevant knot

Tight lines

Dave

This Carp Catchers Blog is going to show how to tie the 5 Turn Twice Through The Eye Clinch Knot. The Clinch Knot is an improvement on the blood knot. It was devised by carp fishing pioneer Jim Gibbinson and is a real belt and braces knot. The 5 turn clinch knot is normally used to attach swivels but there is no reason it could not be used to attach hooks. Ok carp catchers lets get started.

Step 1

Thread your line through the swivel

Step 2

Thread it through again

Step 3

Pull the tag end through about 6” from the swivel and lay alongside the mainline or hooklink

Step 4

Whip the tag up over the mainline or hooklink back towards the swivel as per photo. Do this 5 times

Step 5

Tread the tag end through the loop created at the swivel end

Step 6

Thread the tag end through the loop created at the opposite end to the swivel

Step 7

Moisten and carefully bed down the knot. Cut off tag end

                                                                                      5 Turn Clinch Knot

Best fishes,

John