Carp Catchers Blog

The Seaguar knot was specifically designed for attaching fluorocarbon to monofilament. Fluorocarbon has become very popular in recent years with carp anglers due to its sinking and invisibility properties when submerged in water. However fluorocarbon has a very poor tolerance for incorrectly used and poorly tied knots. The Seaguar knot forms a reliable connection between fluorocarbon and monofilament, is easy to tie and the finished knot is neat and does not compromise the strength of either material.

Below are two ideal products for tying fluorocarbon leaders with.

Korda IQ Fluorocarbon

Step 1.

Hold the monofilament and fluorocarbon leader together.

Step 2.

Form a large loop in the leader and mainline.

Step 3.

Twist both loops anticlockwise three times.

Step 4.

Pass the tag end and the entire leader through the loop.

Step 5.

Moisten and pull all four ends to tighten. Trim the tag ends and your done.

Give it a go.

Tight Lines

Dave

One of the problems with using leadcore is the size of the knot used to attach it to the mainline. In a previous blog I showed you how to tie a proper needle knot, which is an extremely small and strong knot. In this blog I am going to show you a very good alternative devised by Keith Moors. Keith used to write for the mags in this country before he bought a carp fishery in France and moved there. Anyway on with the demo.

These are the components used to tie the knot.

I’ve used the ESP Bulk Spool Leadcore  in sandy gravel as I find it really easy to work with. I’ve used the Korda Fine Baiting Needle because it has a really wide body which helps to stretch out the leadcore sheath making easier to thread things through.

Step 1

Pull out about 2 inches of the lead

 

Step 2

Trim off the lead

 

Step 3

Singe the end of the leadcore sheath with a lighter to stop the sheath fraying.

 

Step 4

Loop the end of your mainline

 

Step 5

Trap the loop in the needle and close the latch of the needle

 

Step 6

Pull the looped mainline through the leadcore sheath, it should look like this

 

Step 7

Thread the end of the leadcore down through the loop

 

Step 8

Pass the leadcore over the bottom part of the loop

 

Step 9

Thread the leadcore over and under the top part of the loop

 

Step 10

Thread the leadcore over and under the top part of the loop again

 

Step 11

Gentley tease down the knot, then pull down tight

 

Step 12

Pull back the leadcore sheath to expose the tag end

 

Step 12a

Snip off the tag end

 

Step 14

Let the sheath go and you have your finished leadcore leader knot. Small, strong and unobtrusive!

 

Best fishes

John

The Albright Knot is the perfect knot for joining mono to braid, which makes it the ideal knot for combi link rigs or leaders. Below is a step by step photographic sequence showing how to tie The Albright Knot.

Step 1

Form a loop in your mono or fluorocarbon.

Step 2

Thread your braid through the nylon loop

Step 3

Whip the braid around the nylon going away from the loop about 5-6 turns. if you

are a belt and braces person you can whip another 5-6 turns going back towards

loop but I have never found it necessary. The version shown makes for a neater

more unobtrusive knot.

Step 4

Thread tag end of the braid back through the nylon loop the same way it came in

Step 5

Gently tease the knot together

Step 6

Bed the knot down tightly, it is probably best not to moisten this knot before tightening

Step 7

Trim tag ends

Step 8

The finished Albright Knot.

Best fishes,

John

The Needle Knot is a very small neat knot used to tie a mainline to a leadcore leader. As for knot strength the needle knot rates at approximately 100%. The kneedle knot is the prefered knot when considering carp safety as due to its compactness it allows beads, hooklinks, rings etc. to slide of easily in the event of the mainline breaking. The Items you will need to tie this knot are leadcore in this instance I am using ESP Bulk Spool Leadcore  in the Choddy Silt colour, a largish sewing needle, a lighter, some scissors and your mainline obviously.

Step 1

Pull out an inch or two of the lead from the leadcore.

Step 2

Snip of the lead wire

Step 3

Insert the kneedle into the empty leadcore sheath and seal the fibres with the lighter to prevent fraying

Step 4

Thread your mainline through the kneedle and thread the kneedle through the leadcore and out of the side approx. half an inch in

Step 5

Pull the kneedle and mainline through the leadcore sheath

Step 6

Lay the kneedle alongside the leadcore sheath like so

Step 7

Whip the mainline around the leadcore and kneedle 5-6 times in the direction of mainline

Step 8

Thread the tag end of the mainline through the eye of the kneedle

Step 9

Pull the kneedle and tag end through the loops created by the whipping

Step 10

Moisten the knot then slowly pull the mainline and tag end in opposite directions to bed down the knot

Step 11

Carefully snip of the tag end

The Finished Kneedle Knot

Your knot should look even neater as I have used an extremely thick line for photographic clarity.

If you are finding the blog useful and informative why not put it in your favourites folder or bookmark it. Also any comments would be welcome (keep them clean!).

Best fishes,

John�