Carp Catchers Blog

The Shot On The Hair Rig is basically a bottom bait rig with a small shot added to the hair to allow a pop-up hookbait to be used. This completely alters how the rig to reacts to how it would with a bottom bait. The hookbait is allowed to move more naturally due to it’s bouyancy and the length of the hair. The shot on the hair allows you to either critically balance or overweight the pop up hookbait.  The nature of supple braid allows the hookbait to be picked up with minimal resistance and the pattern of the hook means the point hangs low below the hookbait helping it to grab hold. The simplicity of The Shot On The Hair Rig makes it easy to tie and it minimises the bulky components such as shrink tubing used on some rigs.

For the purpose of this demonstration I used the Korda Supernatural Hooklink, a Korda Kurv Shank Hook and a No.4 split shot. The shot size is determined by the size and bouyancy of your choosen pop-up, the bigger and more bouyant the pop-up the larger the shot. I found a No.4 shot to work perfectly with a 14mm Richworth Pineapple Hawaiian Pop Ups  although it varies between different makes and types of pop-ups.

Step 1.

Cut 14″ of Korda Supernatural from the spool and tie a small overhand loop knot in one end.

Step 2.

Thread on your choosen pop-up and secure in place with a bait stop.

Step 3.

For this version of the rig pinch the shot onto the hooklink below the pop-up. This will give you a slow sinking hookbait which is almost critically balanced. We will show you an alternative version of this rig, which has  the shot positioned differently, soon.

Step 4.

Thread the Korda Kurv Shank Hook onto the hooklink passing the braid though the back of the eye to the front and position the bait about 6mm from the top of the hook.

Step 5.

Now whip the hooklink up the shank of the hook 6-7 times and then pass the hooklink through the back of the eye to the front to finish the knot.

Step 6.

Double over the other end of the hooklink.

Step 7.

Then form a loop with the doubled over section of the hooklink.

Step 8.

Now pass the end of the doubled over section around the bottom and through the back of the loop created in step 7.

This creates the figure of eight, if you get this eight shape then you have done it right.

If you struggle with tying the knot then try this method. Alternative Figure of Eight Loop Knot.

Step 9.

Now gently tighten down the knot and trim the tag end.

The rig is now complete and ready to be attached to your lead setup.

The rig is best fished of with a small Dynamite Stick or PVA Mesh Bag thread down the hooklink over the hook to avoid tangles.

Tight Lines

Dave

The Solar Quick Change PVA Bag System is ideal for anglers who use PVA bags for the majority of their angling. The system will ensure you don’t lose the bag on the cast while improving casting distance and accuracy. The system is designed to be anti tangle and works with any inline lead.

For the purpose of this demonstration I used a Korda Flat Pear Inline Lead, Solar Contour Super Supple Rig Tubing and Korda Size 8 Ring Swivels  was used between the helicopter beads for the rig to be attached to.

Step 1.

Thread your mainline through your desired length of the Solar rig tubing.

Step 2.

Now thread 1 of the beads provided with the Solar PVA System onto the rig tubing followed by the Korda Ring Swivel followed by another bead. If you’re using mainline straight through there is silicone tubing provided for the beads to the grip. If you’re using leadcore then please ensure all beads can be pulled free of the leader to ensure the lead will be lost in the event of your line breaking. Tie or loop your hooklink to the ring swivel.

Step 3.

Now thread on one of the sleeves provided and push the tubing securely inside.

Step 4.

Then gently push the insert out of your choosen inline……

…..and thread it onto your mainline.

Step 5.

Tie a Figure Of Eight Loop Knot  in the end of your mainline and attach the Solar quick change PVA bag clip like so.

Step 6.

Now pull the lead over the clip followed by the sleeve and rig tubing. The finished setup should look like this.

All you have to do to attach a PVA bag is to pull the clip out of the bottom of the lead and hook a PVA bag on before pulling the clip back inside the lead. Then just thread the hook through the mesh of the bag and your ready to cast out.

This set up is particularly well suited to adding freebies with the Mag Aligner Rig and really comes into it’s own during the winter months.

Give it a go.

Tight lines

Dave

The Atomic Tackle Maggot Rig uses the inline lead setup fished helicopter style allowing a large PVA stocking of maggots to be tied to the swivel at the base of the lead. This enables the hook to be secured to the PVA stocking so once cast out the PVA bag will melt leaving your maggot hookbait lying in amongst the other maggots.

For the purpose of the demonstration I used a Gardner Readymade Mag Aligner Rig.

Step 1.

Pull out the large ring swivel from the base of the lead.

Step 2.

Now thread your mainline through the lead. ( If using leadcore or a leader, you will need to splice or loop the swivel on)

Step 3.

Tie your mainline to the swivel, I would suggest a palomar knot. To tie a palomar knot double over your mainline and pass it through the eye of your swivel.

Then tie an overhand knot with the doubled over mainline.

Now pass the swivel through the loop made by the overhand knot.

Then moisten the knot, slowly tighten it down and trim the tag end.

Step 4.

Once the knot is tied pull the swivel into the insert in the base of the lead.

Step 5.

Now you need to either tie your rig to the swivel above the lead. If the rig has a loop in the end pass the loop through the swivel before passing the hookend of the rig through the loop and tightening as I’ve done in this demonstration.

The finished rig should look like this.

The large ring at the base of the lead is for the PVA mesh bag to be tied to, then all you need to do is push the hook through the PVA mesh to secure it for casting.

Give it a go.

Dave

The Guru Pellet Cones  are an innovative alternative to PVA bags that enables an angler to present a small pile of feed around the hookbait. The tangle free presentation that the pellets cones provide is ideal for use with small soft pellets or groundbait.

The pellets I used in this demonstration were Dynamite Baits Marine Halibut Pellets.

If your using groundbait or softened pellets start from step 4. If your using harder pellets and are scolding them follow steps 1-3 first.

Step 1.

Pour the pellets into the bottom of a bait container.

Step 2.

Now pour boiling water over the pellets until they are all just covered over with the water and leave for 20-30 mins.

Step 3.

After 20-30 mins the pellets should still resemble their original shape but they should be soft to touch and lighter in colour.

Step 4.

Now take the pellet cone and hold it from the thin end.

Step 5.

Gently scoop some pellets into the cone, compressing them in as you go.

Step 6.

Once the cone is full compress it firmly with finger and thumb.

Step 7.

Now pass the fine baiting needle through the pellet cone, going in from the wider end and out the thinner end. Your now ready to pull your baited rig through the pellets, once you’ve pulled your rig through remove the cone and its ready to cast out.

The compressed pellets will look like so when attached to your rig.

Once cast out the pellets will hold together until they reach the bottom.

Within 30 seconds they will have broken down leaving a small neat pile of bait around your hookbait…..

Give them a go.

Tight Lines

Dave

A method that works well over a bed of scattered boilies is mesh PVA bags of boilies. Using something like  Korda Boilie Funnel Web , a tight mesh bag can be created that practically explodes in the water spreading your hookbait and freebies a few inches apart making the trap less obvious to wary carp. The method is to tie a mesh bag with three boilies in a triangular shape as tightly as possible to create the tension in the PVA, which is needed to throw the baits apart upon melting.  When in the water PVA tightens and pulls the boilies even tighter together before the bags burst and catapulting the baits in seperate directions. The triangles are better than the normal linear mesh bag over choddy bottoms as the hook sits in the middle keeping it clear of any chod. However they obviously will not cast as well.

To tie these PVA bags you need some Korda Boilie Funnel Web PVA, scissors and some boilies, these are air dryed Mainline Activ-8 .

Step 1.

Place three boilies in the boilie funnel web tube and allow them to drop out of the bottom into the PVA mesh. If you are using baits over 16mm then I’d suggest using the largerKorda funnel web size as you won’t be able to create the right shape with the larger baits in the boilie funnel web, for baits 16mm and under the boilie funnel web is best.

Step 2.

Now push the baits into a triangular shape and tighten the PVA holding the baits as close together as possible to create a bait triangle.

Step 3.

Holding the boilies in position tie off the bag, again trying to hold the baits as tight as possible. The tighter the bag the better presentation you will achieve.

Once you have trimmed the tag ends of the knots tied in the bag you should have a mesh bag that looks like this. (See Picture Below).

The mesh bag can be hooked on or alternatively you can thread the hooklink through the middle of the baits and pull you hook through to sit between the three baits, this can actually help the slow the rig down as it travels through the water so might be worth a go fishing over softer lakebeds and as I said earlier keep the hook clear of any chod.

Here is a couple of pictures demonstrating the presentation this bag will give your freebies.

The bag still intact.

15-20 seconds after contact with the water.

Give it a go

Tight lines

Dave

Starting with PVA mesh which comes on tubes for easy bag making. PVA mesh is available in a range of sizes, for example Korda do PVA mesh in 3 different widths, Standard funnel web for tying up small golf ball size bags of pellets and crushed boilies etc,  Boilie Funnel Web PVA for making up bags of boilies instead of a stringer or dynamite sticks of groundbait which can be threaded down your hooklink and prevent tangles as well as leaving a neat little pile of groundbait next to you hookbait and finally there is longchuck funnel web which is designed for making smaller dynamite sticks which can be cast further distances. This presentation using PVA mesh is preferred by many due to it being quick and convenient.

Solid PVA bags such as the  ESP PVA Bags is the next method which involves placing your whole rig including your lead into a bag which is filled with free offerings and can be used in any situation, even cast straight into weed. Solid bags need to be punctured once tied to make sure that the bag sinks to the bottom and doesn’t float.

PVA tape for example Krystons’s Super Grip Stringer Tape can be used to make up bait stringers where several baits can be threaded onto the PVA and hooked onto you rig to present a small amount of baits tight to your hookbait. They can also be used to tie your hair to the shank of your hook to prevent tangles when casting.

PVA nuggets such as Gardner’s Rigwise Dissolving Rig Foam are the last of the PVA products used by carp anglers, they can be used to prevent your hook snagging on any lakebed debris when casting to areas which aren’t that clear as well as using them as a marker to fire baits at once you’ve cast your rig into your swim.

Tight Lines

David