Carp Catchers Blog

This is a simple surface rig that will compliment the Korda Surface Controllers or any other surface set up.

To tie this rig you will need some Korda Cruiser Control Surface Line, Korda Mixa Hooks, some Enterprise Imitation Dog Biscuits and a Korda Size 11 Ring Swivel.

Step 1.

Remove about 3-4 foot of Korda Kruiser Control Surface Line and tie a small loop knot in one end.

Step 2.

Now thread on an Enterprise Imitation Dog Biscuit. Place one of the supplied shot in the hair loop and pinch in place, then pull it tightly into the recess in the biscuit.

Step 3.

Pass the other end of the line through the back of the eye of the Korda Mixa hook and position it below the bait. Then hook the imitation mixer on the side opposite the shot.

Step 4.

Whip the line up the shank of the hook 6 times making sure the first whip goes away from the join in the eye.

Step 5.

Now whip the line once back down the shank of the hook.

Step 6.

Pass the line through the back of the eye again and moisten before tightening down gently.

Step 7.

Now slide the hook round further so the shank is inside the imitation dog biscuit with the point of the hook free to get a hook hold.

Step 8.

Tie the other end of the hooklink to a size 11 ring swivel using a palomar knot. Double over the end of the hooklink and pass it though the big eye of the swivel.

Step 9.

Now form an overhand knot in the doubled over section of the hooklink around the swivel.

Step 10.

Pass the swivel through the loop in the end of the hooklink which was made when the overhand knot was formed.

Step 11.

Moisten the knot and tighten it down gently before trimming the tag end.

The rig is now ready to be attached to your surface setup and cast out.

Give it a go.

Tight Lines

Dave

The Korda Interceptor is a new distance surface controller. The design of the controller allows you to change the weight of the controller without having to break down your setup. The controller has a self orientating high viz sight, is very aerodynamic for long range casting with minimal tangles and is made with a low visibility surface colour plastic.

To setup one up you will need a Korda Interceptor and a Korda size 11 ring swivel.

Step 1.

Thread your mainline through the rigid tube.

Step 2.

Slide the soft insert onto your mainline and push the rigid tube inside it.

Step 3.

Now tie on the size 11 ring swivel using a Palomar knot. Double over the end of your mainline and pass it through the eye of the swivel.

Step 4.

Tie and overhand knot around the swivel with the doubled over section of your mainline.

Step 5.

Then pass the swivel through the loop created in the doubled over mainline once the overhand knot has been formed.

Step 6.

Moisten the knot and tighten it down slowly, before trimming the tag end.

Step 7.

Gently pull the swivel into the soft insert.

Step 8.

Locate the slot on the side of the interceptor body and place your mainline in the slot.

Step 9.

Slide the interceptor down the rigid tube until is sits firmly on the soft insert.

The Interceptor is now ready for you to attach your hooklink and cast out.

Give it a go. To purchase any of the items shown please click on the above links.

Dave

For you surface fishing enthusiasts we have the new Korda floater gear in stock now. The Korda Interceptor Controller  is for distance surface fishing. The Interceptor controller has some very clever design features. It will always land the same way up with the orange sight tag on top making it easy to spot. The body of the Interceptor has a slit running along it’s length, which allows you to change bodies without having to break your set up down. Finally the colour, we all know Korda’s track record with underwater filming, well the colour of the Interceptor was the one least visible underwater. For more information or to purchase please click on the above link.

The Korda Kruiser Controller  is a totally unique design. The innovative line attachment makes it virtually tangle free. The Kruiser Controller needs no lead or extra weight resulting in quiet water entry. It is the same low visibilty green as the Interceptor. For more information or to purchase please click on the above link.

The Korda Mixa Hooks  are the first hook specially designed for surface fishing. They have a silky smooth PTFE coating preventing reflective glint, which could spook wary fish. The Mixa Hook is flat forged for extra strength and has a super short shank for added lightness. They are available in both barbed and barbless patterns. For more information or to purchase please follow the above link.

Finally we have the  Korda Kruiser Control Floater Line   has again been specifically designed for surface fishing. It is super soft and supple to ensure easy casting of even the lightest controller. Kruiser Control has a low gloss finish and near neutral buoyancy ensuring that it lies unobtrusively in the surface film. It has limited stretch minimising hookpulls. For more information or to purchase please click on the above link.

                                                                                         Korda Interceptor Controller

                                                                                              Korda Kruiser Controller

                                                                                               Korda Mixa Hook

Best fishes,

John

This Carp Catchers Blog is for those of you who like or would like too do a spot of surface carp fishing. It is fairly easy but there many people that are new to carp fishing so here goes.

These are the components needed for the set up.

Step 1

Loop your mainline through one of the Line/Rig Stops  loops

Step 2

Push one of the line stops towards your mainline

Step 3

Push the line stop onto the mainline loop

Step 4

Push line off mainline onto the mainline itself

Step 5

Cut off the kink in mainline caused by looping it

Step 6

Pull the line stop right up your mainline and thread the mainline through your TFG Surface Missile

Step 7

Tie on one of the size 11 ESP Hi Performance Carp Swivels  using a Palomar Knot

Step 8

Pull the Surface Missile up tight to the swivel

Step 9

Pull the line stop up to the back of the missile. This is what will give a bolt effect to the rig

Step 10

The finished rig. Tie on your hooklink and you are ready to go

This is a carp safe rig in that most surface fishing hooklinks are of a light breaking strain. Should the mainline break the line stop will come off fairly easily. The whitish or opaque finish of the missile will blend in with the whitish/light blue of the background(sky). Don’t forget the carp are looking up!!

Best fishes,

John