Carp Catchers Blog » Carp Fishing

He Who Dares!!

admin — Sat, 07 Jan 2012 14:21:20 +0000

During a recent winter session, when the lake was empty and all the other anglers were at home I landed 7 fish to 25lb 2oz. All the fish were landed using snowman hookbaits presented on helicopter rigs incorportating Atomic Jel-E-Wyre Hooklinks and Korda Wide Gape Hooks. The snowman hookbaits were topped with Mainline Hi-Visual Tutti Frutti 10mm Pop-ups.

Get out there and get catching.

Tight Lines

Dave

Merry Christmas!!

admin — Sat, 17 Dec 2011 17:13:46 +0000

A Merry Christmas And Happy New Year To All Our Customers, Carp Catchers Blog Readers And Contributers

John, Angela & David

Guru Inline Pellet & Method Feeders – How To

admin — Sat, 19 Nov 2011 17:01:17 +0000

Guru produce two types of inline feeders, the Guru Inline Method Feeder and the Guru Inline Pellet feeder. They are setup the same way but are used with different bait loaded onto the feeder. The Guru Pellet feeder is designed to be used with soft scaulded pellets as loose feed in the feeder and the Method feeder is to be used with a method mix moulded around one side of the feeder, both giving similar presentations with different baits. Both of the Guru feeders come in two sizes, 24 grams and 28 grams.

Step 1.

Remove the small tail rubber and swivel from either end of the feeder, like so.

Step 2.

Now thread you mainline through the tail rubber (Narrow end first) and the feeder.

Step 3.

Attach the swivel supplied to the end of your mainline using a Palomar knot.

Step 4.

Push the tail rubber back into place at the top of the feeder, then pull the swivel back into the bottom of the feeder.

Now to attach the hooklink. If you buy Guru’s readymade hair rigs they will come with a loop tied in the end but if you like to tie your own then tie a loop in the end using a Figure of eight loop knot.

Step 5.

Pass the looped end of the rig though the swivel of the feeder.

Step 6.

Now pass the hook though the loop at the end of the rig.

Step 7.

Pull the hook end of the rig until everything tightens down. The rig will look like this.

Your feeder is now ready to be baited and cast out.

Give them a go. To purchase either the pellet or method feeders click on the the above links.

Dave

Tackling Illegal Imports

admin — Sat, 12 Nov 2011 16:40:34 +0000

I’m sure a lot of you are aware of the problem with illegal importations of large carp into the this country and the risks it possess to our current fish stocks. The Centre for Environment, Fisheries and Aquaculture Science (Cefas) have released this short video to raise the awareness of illegal importations and the dangers involved.

Tackling Illegal Importations Video

Take a quick look, its a very interesting and potentially eye opening video to those of you who are unaware of what goes on with the importation of illegal imports.

Dave

It’s Boilie Time!

admin — Sat, 05 Nov 2011 16:37:54 +0000

Its that time of year again when boilies come into there own and tend to out catch most other baits. During the Autumn as the temperatures are dropping and the days are getting shorter the carp begin to have a feed up for the coming winter months and boilies are one bait they know are good for them. During a recent session on my syndicate I landed this 26lb Mirror carp on a 15mm bottom bait topped with a 10mm Mainline Tutti Frutti Hi-Visual Pop-up over a small bed of mixed size boilies. Use a good quality boilie like Mainline Fusion Or Nash Scopex Squid.

Get yourself some boilies and go catch ‘um!

Tight Lines

Dave

Guru Pellet Feeder – How To

admin — Sat, 15 Oct 2011 15:55:02 +0000

The Guru Pellet Feeder is an innovative design that protects the softened pellet loaded into the feeder during the cast and on impact with the water but allows the loose pellet and hookbait to come free of the feeder once on the lakebed. Here is a step by step guide of how to load the feeder.

Step 1.

Take some standard off the shelf pellets, such as, Trout or Halibut pellets and cover them in boiling water for a couple of minutes before draining the water off.

Check the pellet is sufficiently softened, if not repeat the process with boiling water until they are the right consistency.

For the purpose of this demonstration I only prepared enough pellet for one feeder. If you are planning a day session I would suggest you prepare as much as you think you may need.

Step 2.

Attach the feeder to your mainline, followed by a rig and your choosen bait. I would suggest something that matches the pellet in the feeder.

Step 3.

Partly fill the feeder with the scaulded pellet.

Step 4.

Then place the hookbait in the feeder like so.

Step 5.

Now top up the feeder and compress slightly. Make sure not to compress the pellets too much though, as you want them to loosen and release the hookbait once on the lake bed.

Your feeder is now loaded and ready to cast out.

The feeder will land on the lakebed with the pellet still intact.

But after a minute or so and a gentle pull back of the feeder from the rod it will release the pellet and your hookbait.

This type of presentation is perfect for any waters where weed is present or you are fishing in a greater depth than normal. Although it will work perfectly on all waters.

Give it a go.

Dave

Solid Bags Do It Again!

admin — Thu, 06 Oct 2011 09:02:01 +0000

After another weekend session on my Nene Valley syndicate I managed to bank 2 carp to 24lb. The fish were landed using Korda Solidz PVA Bags filled with PVA friendly hemp, which was made by drying off some Dynamite Baits Frenzied Hempseed and adding a generous amount of Mainline Hemp Oil and leaving it to soak in for atleast an hour. Dynamite Baits Frenzied Monster Tiger Nuts where critically balanced and used as hookbaits with Avid Carp Sight Stops for added visual attraction.

Tight Lines

Dave

Seaguar Fluorocarbon Leader Knot

admin — Sat, 01 Oct 2011 15:41:06 +0000

The Seaguar knot was specifically designed for attaching fluorocarbon to monofilament. Fluorocarbon has become very popular in recent years with carp anglers due to its sinking and invisibility properties when submerged in water. However fluorocarbon has a very poor tolerance for incorrectly used and poorly tied knots. The Seaguar knot forms a reliable connection between fluorocarbon and monofilament, is easy to tie and the finished knot is neat and does not compromise the strength of either material.

Below are two ideal products for tying fluorocarbon leaders with.

Korda IQ Fluorocarbon

Step 1.

Hold the monofilament and fluorocarbon leader together.

Step 2.

Form a large loop in the leader and mainline.

Step 3.

Twist both loops anticlockwise three times.

Step 4.

Pass the tag end and the entire leader through the loop.

Step 5.

Moisten and pull all four ends to tighten. Trim the tag ends and your done.

Give it a go.

Tight Lines

Dave

Oxlease Thirty

admin — Sat, 03 Sep 2011 16:04:16 +0000

I made another trip down to Richworth Linear Fisheries recently and had another good result. I landed 12 fish during my session the biggest being a 30lb 4oz Mirror. All the fish fell to either critically balanced tiger nut or boilie hookbaits with Avid Carp Sight Stops fished at 85 yards to the island over a spodded area of hemp, corn, chops, maggots, pellets and crushed tigers. Baits were presented in Extra Small Korda Solidz PVA Bags using 2.5oz Avid Carp Inline Groove Leads and short hooklinks.

Tight Lines

Dave

A Nice Return

admin — Thu, 01 Sep 2011 09:50:29 +0000

After a year with virtually no carp fishing I had a nice return to my syndicate. The 32lb 2oz mirror carp shown below was my reward. It was caught on 18mm Mainline Activ 8 Boilies. My rig was tied old school D rig style with 30lb GLT No Can See Fluorocarbon to a size 6 Gardner Longshank Incizor hook.

Best Fishes,

John