Carp Catchers Blog

The Shot On The Hair Rig is basically a bottom bait rig with a small shot added to the hair to allow a pop-up hookbait to be used. This completely alters how the rig to reacts to how it would with a bottom bait. The hookbait is allowed to move more naturally due to it’s bouyancy and the length of the hair. The shot on the hair allows you to either critically balance or overweight the pop up hookbait.  The nature of supple braid allows the hookbait to be picked up with minimal resistance and the pattern of the hook means the point hangs low below the hookbait helping it to grab hold. The simplicity of The Shot On The Hair Rig makes it easy to tie and it minimises the bulky components such as shrink tubing used on some rigs.

For the purpose of this demonstration I used the Korda Supernatural Hooklink, a Korda Kurv Shank Hook and a No.4 split shot. The shot size is determined by the size and bouyancy of your choosen pop-up, the bigger and more bouyant the pop-up the larger the shot. I found a No.4 shot to work perfectly with a 14mm Richworth Pineapple Hawaiian Pop Ups  although it varies between different makes and types of pop-ups.

Step 1.

Cut 14″ of Korda Supernatural from the spool and tie a small overhand loop knot in one end.

Step 2.

Thread on your choosen pop-up and secure in place with a bait stop.

Step 3.

For this version of the rig pinch the shot onto the hooklink below the pop-up. This will give you a slow sinking hookbait which is almost critically balanced. We will show you an alternative version of this rig, which has  the shot positioned differently, soon.

Step 4.

Thread the Korda Kurv Shank Hook onto the hooklink passing the braid though the back of the eye to the front and position the bait about 6mm from the top of the hook.

Step 5.

Now whip the hooklink up the shank of the hook 6-7 times and then pass the hooklink through the back of the eye to the front to finish the knot.

Step 6.

Double over the other end of the hooklink.

Step 7.

Then form a loop with the doubled over section of the hooklink.

Step 8.

Now pass the end of the doubled over section around the bottom and through the back of the loop created in step 7.

This creates the figure of eight, if you get this eight shape then you have done it right.

If you struggle with tying the knot then try this method. Alternative Figure of Eight Loop Knot.

Step 9.

Now gently tighten down the knot and trim the tag end.

The rig is now complete and ready to be attached to your lead setup.

The rig is best fished of with a small Dynamite Stick or PVA Mesh Bag thread down the hooklink over the hook to avoid tangles.

Tight Lines

Dave

The Solar Quick Change PVA Bag System is ideal for anglers who use PVA bags for the majority of their angling. The system will ensure you don’t lose the bag on the cast while improving casting distance and accuracy. The system is designed to be anti tangle and works with any inline lead.

For the purpose of this demonstration I used a Korda Flat Pear Inline Lead, Solar Contour Super Supple Rig Tubing and Korda Size 8 Ring Swivels  was used between the helicopter beads for the rig to be attached to.

Step 1.

Thread your mainline through your desired length of the Solar rig tubing.

Step 2.

Now thread 1 of the beads provided with the Solar PVA System onto the rig tubing followed by the Korda Ring Swivel followed by another bead. If you’re using mainline straight through there is silicone tubing provided for the beads to the grip. If you’re using leadcore then please ensure all beads can be pulled free of the leader to ensure the lead will be lost in the event of your line breaking. Tie or loop your hooklink to the ring swivel.

Step 3.

Now thread on one of the sleeves provided and push the tubing securely inside.

Step 4.

Then gently push the insert out of your choosen inline……

…..and thread it onto your mainline.

Step 5.

Tie a Figure Of Eight Loop Knot  in the end of your mainline and attach the Solar quick change PVA bag clip like so.

Step 6.

Now pull the lead over the clip followed by the sleeve and rig tubing. The finished setup should look like this.

All you have to do to attach a PVA bag is to pull the clip out of the bottom of the lead and hook a PVA bag on before pulling the clip back inside the lead. Then just thread the hook through the mesh of the bag and your ready to cast out.

This set up is particularly well suited to adding freebies with the Mag Aligner Rig and really comes into it’s own during the winter months.

Give it a go.

Tight lines

Dave

The KD Rig is named after Kenny Dorset the angler who developed it. The KD rigs advantage is that it increases bait separation and kicks the hook out at a more aggressive angle than the standard knotless knot. I have seen it tied using braid, but in my opinion a soft hooklink and a soft hair will negate the supposed above advantages. However many of the braid tied variations that I’ve seen are pop up rigs with a shot on the hair. In this demonstration I have used a soft fluorocarbon, which is still stiff enough to provide the above advantages ie. increased bait separation and an aggressive hooking angle. If you want to use a pop up with the stiffer version shown here you will need to put some tungsten putty on the hooklink itself. This will make this version of the KD rig an even better hooker in my opinion than the braid tied one. If anyone would like me to expand on the bait separation issue which I think is crucial to most rig mechanics please leave a comment. The components I used to tie the KD rig are ESP Soft Ghost  and Gardner Incizor Carp Hooks 

Step 1

Cut a length of the Ghost Fluorocarbon and tie a small overhand knot for the boilie stop

Step 2

Thread on your boilie and put a boilie stop in the loop. The reason for putting the boilie on before you tie the rig is to enable you to set the hair to the correct length.

Step 3

Set the hair so that there is a 10cm gap between the bottom of the bait and the top of the hook

Step 4

Thread the end of your Ghost hooklink through the eye of the hook

Step 4

Whip two turns of your hooklink around the shank making sure to whip away from the join in the eye of the hook

Step 5

Now let the bait drop and whip a further 3 to 5 turns under the hair

Step 6

Thread the tag end of the Ghost as per photo

Step 7

Moisten and bed down the knot here I am using The Korda Pulla Tool

Step 8

Tie a figure of eight loop knot at the other end, moisten and bed down. If you don’t know how to tie this knot see previous blog

The finished KD Rig

Best fishes

John

The Figure Of Eight or Double Overhand Loop Knot is an extremely strong loop knot with many applications. Below is a step by step photographic sequence showing you how to tie it.

Step1

Choose your hooklink material and cut the desired length. I have chosen Sufix Camfusion 15lb for this demonstration.

Step 2

Double the hooklink over and form loop to the approximate size that you require for your rig.

Step 3

Form another loop in the doubled over hooklink material

Step 4

Thread the end of the first loop through the second loop

Step 5

Thread the end of the first loop through the second loop again

Step 6

Gentley tease the knot down, this is the figure of eight

Step 7

Moisten the knot with saliva and bed down then trim off the tag end. The finished Figure Of Eight Or Double Overhand Loop Knot.

Hope this is of use, any comments would be welcomed and appreciated.

Best fishes,

John