Carp Catchers Blog

The new ATTS Bite Alarms and Nash Box Logic TT Rig Station have just come in. These babies will make the Ideal christmas presents for carpers everywhere. I’ll do a short review on them below, for more details and to purchase them go to the main site via the links.

ATTS Bite Alarms – ATTx V2 Receiver

The New ATTS Bite Alarms are the ultimate tackle tarts item. However you don’t need to be a tackle tart to appreciate and make use of their unique features. The ATTS’s most unique feature is that it is the first silent alarm, the audible alarm is given by the ATTx V2 Remote receiver. There has been a lot in the media recently about sound travelling down the line and spooking the carp the ATTS will prevent this. The ATTS is the smallest bite alarm on the market and along with it’s silent function and matt black, soft rubber touch finish, the ATTS is the ultimate stealth alarm.

                             ATTS Bite Alarms

                             ATTx V2 Receiver

Nash Box Logic TT Rig Station

The Nash Box Logic TT Rig Station is absolutely brilliant, I’m just amazed that nobodys produced something like it before now. The TT Rig Station organises and stores all of your terminal tackle, PVA, marker floats, leads etc. The Rig Station also stores all of your rigs and comes supplied with 20 rig pins. The most ingenious part though is that the rig station is just that, it doubles as a work station where you can tie your rigs with everything to hand, you can even critically balance your hookbaits. Check this one out I don’t think you will be disappointed.

                   Nash Box Logic TT Rig Station

Best fishes,

John

Here’s a nice photo of customer James with a double figure pike. James was boat fishing at Pitsford Reservoir and took the fine specimen lure fishing a copper spoon.

Best fishes,

John

The Needle Knot is a very small neat knot used to tie a mainline to a leadcore leader. As for knot strength the needle knot rates at approximately 100%. The kneedle knot is the prefered knot when considering carp safety as due to its compactness it allows beads, hooklinks, rings etc. to slide of easily in the event of the mainline breaking. The Items you will need to tie this knot are leadcore in this instance I am using ESP Bulk Spool Leadcore  in the Choddy Silt colour, a largish sewing needle, a lighter, some scissors and your mainline obviously.

Step 1

Pull out an inch or two of the lead from the leadcore.

Step 2

Snip of the lead wire

Step 3

Insert the kneedle into the empty leadcore sheath and seal the fibres with the lighter to prevent fraying

Step 4

Thread your mainline through the kneedle and thread the kneedle through the leadcore and out of the side approx. half an inch in

Step 5

Pull the kneedle and mainline through the leadcore sheath

Step 6

Lay the kneedle alongside the leadcore sheath like so

Step 7

Whip the mainline around the leadcore and kneedle 5-6 times in the direction of mainline

Step 8

Thread the tag end of the mainline through the eye of the kneedle

Step 9

Pull the kneedle and tag end through the loops created by the whipping

Step 10

Moisten the knot then slowly pull the mainline and tag end in opposite directions to bed down the knot

Step 11

Carefully snip of the tag end

The Finished Kneedle Knot

Your knot should look even neater as I have used an extremely thick line for photographic clarity.

If you are finding the blog useful and informative why not put it in your favourites folder or bookmark it. Also any comments would be welcome (keep them clean!).

Best fishes,

John�

In this third part of which hooklink we will be looking at braided hooklinks. Braided hooklinks are almost self explanatory in that a soft material is braided to give it a smooth finish and extra strength. The most popular material for braids is Dyneema which is the registered name for a super strong polyethylene fiber. Because Dyneema floats it is often braided with another material usually Dacron to counteract its bouyancy. Kevlar another registered name is increasingly becoming more popular as a fiber for braiding due to its incredible resilience. Kevlar is the stuff they use to make bulletproof vests so that tells you how tough it is. It also is braided with other materials such as Dyneema to give it different properties. Some good examples of braided hooklinks are shown below.

Korda Supernatural      Sufix Silky Soft          Super Nova               Sufix Nu-Flex

Braids

Braids were originally used because early carp anglers believed that carp could feel hooklink materials with their lips. Because braids are soft, thin and supple they reasoned that the carp would be less likely to detect them. Nowadays though they are used as a supple hooklink which allows the hookbait to act naturally. Braids are also very useful when using solid PVA bags as the hooklink can be folded into even the smallest bag.

Though braids are usually used to construct supple rigs they are quite commonly used to tie combi-link rigs, this is because supple rigs are easier for the carp to eject. Combi-link rigs are tied with the braid at the hook end knotted to a stiffer boom section which is attached to the swivel. This gives a rig which has a supple hook end, therefore hopefully catching somewhere in the carps mouth with the stiffer boom section making ejection more difficult. Another variation of the combi-link rig is to have a stiff hooklink material at the hookend attached to a braid section running to the swivel.

Carp Care

Finally just a word of caution some fisheries are banning the use of thin braids as they believe they have a cheese wire effect and cut into the scissor area of the carps mouth. If you find that this is happening in your own experience please, please stop using them.

Best fishes,

John

The Leader used in this demonstation is the ESP Tapered Shockleaders tied using the Mahin Knot.

Step 1.

Form a small overhand loop with the shockleader. (See picture below)

Step 2.

Now pass your mainline through the loop. (See picture below)

Step 3.

Then whip the mainline 7 times up the leader. (See picture below)

Step 4.

Now whip the mainline 6 time back the other way and pass it back through the overhand loop. (See picture below)

Step 5.

Moisten the line thoroughly and slow tighten it down so it forms a nice neat knot and trim the tag ends. (See picture below)

The shockleader is now ready to use, the knot needs to be atleast 3 turns onto the spool with the knot positioned at the bottom of the spool to avoid it getting snagged on the cast.

Tight Lines

David