The KD Rig

admin — Tue, 03 Mar 2009 11:50:50 +0000

The KD Rig is named after Kenny Dorset the angler who developed it. The KD rigs advantage is that it increases bait separation and kicks the hook out at a more aggressive angle than the standard knotless knot. I have seen it tied using braid, but in my opinion a soft hooklink and a soft hair will negate the supposed above advantages. However many of the braid tied variations that I’ve seen are pop up rigs with a shot on the hair. In this demonstration I have used a soft fluorocarbon, which is still stiff enough to provide the above advantages ie. increased bait separation and an aggressive hooking angle. If you want to use a pop up with the stiffer version shown here you will need to put some tungsten putty on the hooklink itself. This will make this version of the KD rig an even better hooker in my opinion than the braid tied one. If anyone would like me to expand on the bait separation issue which I think is crucial to most rig mechanics please leave a comment. The components I used to tie the KD rig are ESP Soft Ghost and Gardner Incizor Carp Hooks

Step 1

Cut a length of the Ghost Fluorocarbon and tie a small overhand knot for the boilie stop

Step 2

Thread on your boilie and put a boilie stop in the loop. The reason for putting the boilie on before you tie the rig is to enable you to set the hair to the correct length.

Step 3

Set the hair so that there is a 10cm gap between the bottom of the bait and the top of the hook

Step 4

Thread the end of your Ghost hooklink through the eye of the hook

Step 4

Whip two turns of your hooklink around the shank making sure to whip away from the join in the eye of the hook

Step 5

Now let the bait drop and whip a further 3 to 5 turns under the hair

Step 6

Thread the tag end of the Ghost as per photo

Step 7

Moisten and bed down the knot here I am using The Korda Pulla Tool

Step 8

Tie a figure of eight loop knot at the other end, moisten and bed down. If you don’t know how to tie this knot see previous blog

The finished KD Rig

Best fishes

John

The New Improved Korda Maggot Clip – Rig 1

admin — Tue, 09 Dec 2008 14:16:43 +0000

Now that winters here many of you will be using maggots as bait. In this blog I’m going to show you how to tie a rig with the new improved Korda Maggot Clip . There is more than one rig that can be tied with the maggot clip and I will feature those in future blogs.

These are the components that I used to demonstrate this rig

Step 1

Cut a length of your desired hooklink material, in this case I am using Korda Hybrid Soft

Step 2

Strip off 4-5 inches of the coating

Step 3

Tie a small overhand loop in the stripped section

Step 4

Cut a length, 10mm approximately of the ESP Sink Rig Tube and thread it up towards the loop. The rig tube prevents the live maggots from wriggling around and masking your hookpoint, a little dodge thought up by Nigel Sharp I think.

Step 5

Thread the Korda Maggot Clip through the loop and push the rig tubing tight to the clip

Step 6

Thread the opposite end of the hooklink through the eye of the Atomic Claw hook and whip the stripped section of the hybrid soft up to the rig tubing

Step 7

Thread the tag end of the hooklink through the eye of the hook again and pull to bed down the knot

Step 8

Tie the swivel at the other end of hooklink with a figure of eight loop knot

Step 9

Moisten both knots and pull tight to bed them down. I’m using the excellent Korda Pulla Tool in this shot.

Step 10

Thread on the required number of maggots. I was extremely suprised how easily the maggots went on, so Korda really have improved the sharpness of the clip.

The business end of the finished rig

The finished rig

Best fishes,

John

Carp Catchers Blog » Korda Pulla Tool

The KD Rig

The New Improved Korda Maggot Clip – Rig 1