Carp Catchers Blog

Running rigs are very over looked these days by the majority of carp anglers but if used correctly they can improve your catch rates in the right situation. They are advantageous in that they will give you indication as soon as the bait has moved rather than when the lead moves. Fished with slack lines the running rig setup will give you good indication before the line has even tightened. It also means that if your mainline breaks the lead will be released easily.

For this demonstration I used Korda Safe Zone Sinking Rig Tubing, Korda Safe Zone Run Rig Rubbers, Korda Size 8 Swivels, Korda Ring Clips, Korda Silicone Sleeves and a Korda Pear Lead.

Step 1.

Thread your mainline through your desired length of rig tubing.

Step 2.

Now thread your mainline through the ring on one of the Korda Ring Clips.

Step 3.

Then thread on the Korda Run Rig Rubber and push the rig tubing into the narrow end of the rubber.

Step 4.

With the tag end of you mainline tie a Palomar knot. Double over the tag end and pass it though the eye of a size 8 swivel.

Now tie an overhand knot with the doubled over section of your mainline.

Then pass the swivel through the loop created by doubling over the mainline.

Moisten the knot and tighten it down gently before trimming the tag end.

Step 5.

Pull the swivel inside the Run Rig Rubber.

Step 6.

Now push a silicone sleeve over the swivel of your choosen lead and hold it down so the top eye of the swivel is exposed.

Step 7.

Clip the lead onto the ring clip.

Step 8.

Now slide the silicone sleeve back up over the eye of the swivel and over the ring clip.

Notice how the eye of the swivel attached to the lead has been left exposed, this is to allow the setup to lie flat on the lake bed.

To change to lead all you have to do is slide the silicone sleeve back down and swap the leads.

All that is left to do is attach your rig by either using a Korda Kwik Link or tying it directly to the swivel.

Give it a go.

Dave

The Solar Quick Change PVA Bag System is ideal for anglers who use PVA bags for the majority of their angling. The system will ensure you don’t lose the bag on the cast while improving casting distance and accuracy. The system is designed to be anti tangle and works with any inline lead.

For the purpose of this demonstration I used a Korda Flat Pear Inline Lead, Solar Contour Super Supple Rig Tubing and Korda Size 8 Ring Swivels  was used between the helicopter beads for the rig to be attached to.

Step 1.

Thread your mainline through your desired length of the Solar rig tubing.

Step 2.

Now thread 1 of the beads provided with the Solar PVA System onto the rig tubing followed by the Korda Ring Swivel followed by another bead. If you’re using mainline straight through there is silicone tubing provided for the beads to the grip. If you’re using leadcore then please ensure all beads can be pulled free of the leader to ensure the lead will be lost in the event of your line breaking. Tie or loop your hooklink to the ring swivel.

Step 3.

Now thread on one of the sleeves provided and push the tubing securely inside.

Step 4.

Then gently push the insert out of your choosen inline……

…..and thread it onto your mainline.

Step 5.

Tie a Figure Of Eight Loop Knot  in the end of your mainline and attach the Solar quick change PVA bag clip like so.

Step 6.

Now pull the lead over the clip followed by the sleeve and rig tubing. The finished setup should look like this.

All you have to do to attach a PVA bag is to pull the clip out of the bottom of the lead and hook a PVA bag on before pulling the clip back inside the lead. Then just thread the hook through the mesh of the bag and your ready to cast out.

This set up is particularly well suited to adding freebies with the Mag Aligner Rig and really comes into it’s own during the winter months.

Give it a go.

Tight lines

Dave