Carp Catchers Blog

The Guru Micro Lead Clips provide a fish safe anti tangle option for the Match/Pleasure angler thats suitable for fishing with either leads or feeders. The design of Guru Micro Lead Clip  ensures that your lead or feeder can be released should it become snagged. 

Guru Micro Lead Clips

The leads I used for the purpose of this demonstration were the Guru Square Leads.

Step 1.

Thread your mainline through the tail rubber and then the lead clip.

Step 2.

Double over the tag end of your mainline and pass the loop through the eye of the size 11 swivel provided.

Step 3.

Now tie an overhand knot with the doubled over section of your mainline but don’t tighten it yet.

Step 4.

Pass the swivel through the loop created by the overhand knot.

Step 5.

Now moisten the knot and gently tighten it down.

Step 6.

Pull the lead clip down over the swivel until you hear it click into the clip.

Step 7.

Now clip your lead/feeder on and slide the tail rubber over the lead clip so the angled edge sits the right way on the clip.

All you need to do now is tie on your rig and your ready to cast out. But before doing so make sure the clip is working correctly and the lead will discharge easily. You are now fishing a carp safe set up.

Tight Lines

Dave

Running rigs are very over looked these days by the majority of carp anglers but if used correctly they can improve your catch rates in the right situation. They are advantageous in that they will give you indication as soon as the bait has moved rather than when the lead moves. Fished with slack lines the running rig setup will give you good indication before the line has even tightened. It also means that if your mainline breaks the lead will be released easily.

For this demonstration I used Korda Safe Zone Sinking Rig Tubing, Korda Safe Zone Run Rig Rubbers, Korda Size 8 Swivels, Korda Ring Clips, Korda Silicone Sleeves and a Korda Pear Lead.

Step 1.

Thread your mainline through your desired length of rig tubing.

Step 2.

Now thread your mainline through the ring on one of the Korda Ring Clips.

Step 3.

Then thread on the Korda Run Rig Rubber and push the rig tubing into the narrow end of the rubber.

Step 4.

With the tag end of you mainline tie a Palomar knot. Double over the tag end and pass it though the eye of a size 8 swivel.

Now tie an overhand knot with the doubled over section of your mainline.

Then pass the swivel through the loop created by doubling over the mainline.

Moisten the knot and tighten it down gently before trimming the tag end.

Step 5.

Pull the swivel inside the Run Rig Rubber.

Step 6.

Now push a silicone sleeve over the swivel of your choosen lead and hold it down so the top eye of the swivel is exposed.

Step 7.

Clip the lead onto the ring clip.

Step 8.

Now slide the silicone sleeve back up over the eye of the swivel and over the ring clip.

Notice how the eye of the swivel attached to the lead has been left exposed, this is to allow the setup to lie flat on the lake bed.

To change to lead all you have to do is slide the silicone sleeve back down and swap the leads.

All that is left to do is attach your rig by either using a Korda Kwik Link or tying it directly to the swivel.

Give it a go.

Dave

The Atomic Tackle Maggot Rig uses the inline lead setup fished helicopter style allowing a large PVA stocking of maggots to be tied to the swivel at the base of the lead. This enables the hook to be secured to the PVA stocking so once cast out the PVA bag will melt leaving your maggot hookbait lying in amongst the other maggots.

For the purpose of the demonstration I used a Gardner Readymade Mag Aligner Rig.

Step 1.

Pull out the large ring swivel from the base of the lead.

Step 2.

Now thread your mainline through the lead. ( If using leadcore or a leader, you will need to splice or loop the swivel on)

Step 3.

Tie your mainline to the swivel, I would suggest a palomar knot. To tie a palomar knot double over your mainline and pass it through the eye of your swivel.

Then tie an overhand knot with the doubled over mainline.

Now pass the swivel through the loop made by the overhand knot.

Then moisten the knot, slowly tighten it down and trim the tag end.

Step 4.

Once the knot is tied pull the swivel into the insert in the base of the lead.

Step 5.

Now you need to either tie your rig to the swivel above the lead. If the rig has a loop in the end pass the loop through the swivel before passing the hookend of the rig through the loop and tightening as I’ve done in this demonstration.

The finished rig should look like this.

The large ring at the base of the lead is for the PVA mesh bag to be tied to, then all you need to do is push the hook through the PVA mesh to secure it for casting.

Give it a go.

Dave