Carp Catchers Blog

Running rigs are very over looked these days by the majority of carp anglers but if used correctly they can improve your catch rates in the right situation. They are advantageous in that they will give you indication as soon as the bait has moved rather than when the lead moves. Fished with slack lines the running rig setup will give you good indication before the line has even tightened. It also means that if your mainline breaks the lead will be released easily.

For this demonstration I used Korda Safe Zone Sinking Rig Tubing, Korda Safe Zone Run Rig Rubbers, Korda Size 8 Swivels, Korda Ring Clips, Korda Silicone Sleeves and a Korda Pear Lead.

Step 1.

Thread your mainline through your desired length of rig tubing.

Step 2.

Now thread your mainline through the ring on one of the Korda Ring Clips.

Step 3.

Then thread on the Korda Run Rig Rubber and push the rig tubing into the narrow end of the rubber.

Step 4.

With the tag end of you mainline tie a Palomar knot. Double over the tag end and pass it though the eye of a size 8 swivel.

Now tie an overhand knot with the doubled over section of your mainline.

Then pass the swivel through the loop created by doubling over the mainline.

Moisten the knot and tighten it down gently before trimming the tag end.

Step 5.

Pull the swivel inside the Run Rig Rubber.

Step 6.

Now push a silicone sleeve over the swivel of your choosen lead and hold it down so the top eye of the swivel is exposed.

Step 7.

Clip the lead onto the ring clip.

Step 8.

Now slide the silicone sleeve back up over the eye of the swivel and over the ring clip.

Notice how the eye of the swivel attached to the lead has been left exposed, this is to allow the setup to lie flat on the lake bed.

To change to lead all you have to do is slide the silicone sleeve back down and swap the leads.

All that is left to do is attach your rig by either using a Korda Kwik Link or tying it directly to the swivel.

Give it a go.

Dave

The Atomic Tackle Maggot Rig uses the inline lead setup fished helicopter style allowing a large PVA stocking of maggots to be tied to the swivel at the base of the lead. This enables the hook to be secured to the PVA stocking so once cast out the PVA bag will melt leaving your maggot hookbait lying in amongst the other maggots.

For the purpose of the demonstration I used a Gardner Readymade Mag Aligner Rig.

Step 1.

Pull out the large ring swivel from the base of the lead.

Step 2.

Now thread your mainline through the lead. ( If using leadcore or a leader, you will need to splice or loop the swivel on)

Step 3.

Tie your mainline to the swivel, I would suggest a palomar knot. To tie a palomar knot double over your mainline and pass it through the eye of your swivel.

Then tie an overhand knot with the doubled over mainline.

Now pass the swivel through the loop made by the overhand knot.

Then moisten the knot, slowly tighten it down and trim the tag end.

Step 4.

Once the knot is tied pull the swivel into the insert in the base of the lead.

Step 5.

Now you need to either tie your rig to the swivel above the lead. If the rig has a loop in the end pass the loop through the swivel before passing the hookend of the rig through the loop and tightening as I’ve done in this demonstration.

The finished rig should look like this.

The large ring at the base of the lead is for the PVA mesh bag to be tied to, then all you need to do is push the hook through the PVA mesh to secure it for casting.

Give it a go.

Dave

Most chod rigs nowadays are setup using leadcore or some form of leader but not all fisheries allow leaders whether they be leadcore or otherwise. Using rig tubing is an option which can help get round these bans and can also be used on waters without bans as an alternative to leaders. Rigmarole have designed Chod Rig Beads to fit their Freefall Micro Rig Tubing so that chod rigs can be tied up safely and effectively using the Freefall Micro Rig Tube. The  Rigmarole Freefall Micro Rig Tube is a plastic coated stainless steel coil so it is extremely tough and heavy, it is also very easy to thread.

The components used in this demonstration were Rig Marole Freefall Micro Rig Tube,  Rigmarole Freefall Micro Rig Tube Chod Beads, Rig Marole Tail Rubbers and a Rig Marole Tournament Casting Lead.

Step 1.

Cut the Freefall Micro Rig Tube to your desired length and thread your mainline through it.

Step 2.

Now thread a Freefall Micro Rig Tube Chod Bead onto the tubing, followed by your chod rig and a second bead. Set the beads in place with your chod rig at the required distance up the tubing.

Step 3.

Thread the Rig Marole  Free Fall Tail Rubber onto the line and push the rig tubing into it.

Step 4.

Now tie on your desired lead with a Palomar knot.

Step 5.

Push the swivel into the tail rubber and pull the line tight through the tubing.

The finished rig should look like this. This rig can also be constructed using the Rig Marole Free Fall Rig Tube  and the Rigmarole Freefall Chod Beads. Warning !!! do not superglue the beads or pierce through the side!!!

Tight Lines

Dave

Some interesting news for those of you experiencing problems with knots for fluorocarbon. One of the big American line manufacturers has done some research on knots and fluorocarbon. They found that one of the most popular and strongest knots the palomar, weakened fluorocarbon by up to 30%. Gardner Tackle who have considerable knowledge on fishing lines, suggest using the blood knot, which is usually considered one of the weakest fishing knots. So you might want to consider doing some knot tests yourselves armed with this information.

Best fishes

John